Lutron lut mlc dummy load how to#
Lutron lut mlc dummy load full#

So, my question is who can I talk to about this? I've emailed Lutron today ( Case Number: 7755889 ).Both rooms are on individual dimmer switch. They interrupted constant hot wire from panel box, to the hot to my LED lights. Lights purchased : Sunco 4' recess LED dimmable lightsĪll switches were wired with no neutral connected.

Lutron lut mlc dummy load full#

Lights and dimmer work fine at full power, and dim down fine enough. The lights I purchased were not on the recommended lighting list, and I believe what I am experiencing is the bleed through amperage (5 milli amps) of the Lutron dimmer switch in conjunction with my, smaller than minimum, load is allowing my five lights in my dining room to glow when the dimmer switch is 'Off', and the two lights to glow brighter when their dimmer switch, in my dining room, is 'off' ? There is no ground in either circuit - old home. But then when I turn it off and back on the strobe returns.I am experiencing ghosting, or glowing of my LED's lights, when turning off my lutron casseta switch. When I un-plug the signal device it continues to work great. When I have the 25w signal device in the plug and THEN go to turn it on, it works great. Again my situation is I turn it on either full, or slowly, or from the app or switch, no matter what, it strobes. But I don't think that solves my problem, which is when the light is on it strobes. I mistakenly thought the Lutron setup just worked! Maybe I will give the LUT-MLC a go for now, try it at the sconce box where the neutral is (they say its required to setup), and just see if that solves the issue. I don't want to go through all these hoops if each time I setup a switch it requires some whole new thing to figure out. I am basically putting in two of these switches for lights in front of the garage and separately lights on the porch. Because the outdoor sconce lights, there is a real desire to have the Edison bulbs. Ultimately, I am on the fence about perhaps returning. I also just realized that the non-dimmable Lutron Caseta switch doesn't work in non-neutral switches so that is out the window. The only challenge though is that appears to work for setups where the LEDs flicker when turned off, or ghost when off. I may try the LUT-MLC from Amazon ($10) as I didn't realize that existed. I had replied already from the phone but just wanted to follow up on this one from the computer with more detail in the event anyone had any feedback. Obviously I can't leave the 25 watt signal tester plugged into the outlet forever.

Lutron lut mlc dummy load how to#

Would love some solution that didn't involve $100 synthetic pull thing that I have to figure out how to wire in.

There are some non Edison LED bulbs in the house I could maybe use the dim switches on, and save the single pole non-dimming switches for the front lights.Any help here would be great. My wife loves the Edison look in the see through bulb housing. I liked getting bulbs that could go really bright or I could dim like normal most of the time. Also will the pico switch work with non-dim switches? (if I want an extra switch to have multiple switches for a particular light string)- Anyone else experience this problem or have any solutions?Ultimately the reason I need the Edison bulbs is these are front porch and garage sconces. But happy to hear about others out there.- Does the non-dimming switch have this issue? Wondering if for the lights where I want Edison bulbs I can get those single pole rocker switches that don't dim, and if that has an issue. Does anyone have any dimmable edison LED bulbs they use on their light setup that have worked well? I was considering these 100-watt ST19 dimmable LED vintage bulbs from Home Depot that actually use 15 watts each, and curious if the combined 30 watts is enough for the Lutron switch to work. Here are my questions:- I saw those Lutron synthetic minimum load modules, does that work? I hate the idea of having to buy something else. It appears this has something to do with minimum loads. The reason why they had worked I discovered was because I had a 25 watt signal tester (one of those things that allows you to run a sensor over your electrical panel to detect currents) plugged into a plug socket in line with the lights! I now realize there are issues with under 25 watts in particular on the line. But then later I turn it on and the lights start flashing. On the wall, or with the the app, it was awesome. Had no idea until today there were common issues with Lutron Caseta and Edison bulbs (normal or LED).I installed the Lutron Caseta dimming switch and it worked great.